Crown audio XTi 2002 Power Amplifier
Model: XTI 2002


- You name the price you want to pay for a product.
- If the retailer likes your offer, you get that price for the product.
- Guaranteed Brand New Products
- All Products Sold by Manufacturer Authorized Retailers
- 30 Day Return Policy
-
Free Shipping
No Additional Fees
Packaging Info
Package Weight | 23.75 lb |
Box Dimensions (LxWxH) | 22.5 x 18.9 x 7.1" |
General Information
Input Sensitivity | 1.4Vrms |
Input Impedance | 20k Ohms (Balanced)10 kOhms (Unbalanced) |
Gain | 32.9dB @ 1kHz, 8 Ohm Rated Output |
Frequency Response | (at 1 watt, 20Hz - 20kHz) +0dB, -1dB |
Signal-to-Noise Ratio | XTi1002/2002/4002: 100dB (A weighted)XTi6002: 103dB (A weighted) |
Total Harmonic Distortion (THD) | < 0.5% |
Connections | Input Connectors: XLR, one per channelLink/Out Connector: Loop-thru signal from input connector for linking another amplifier, one per channel.Output Connectors: Two Neutrik Speakon NL4MP output connectors. Channel-1 Speakon is wired with Ch. 1 and Ch. 2 outputs for use with optional single 4-conductor cable. Two binding post outputs (in parallel with Speakon connectors).HiQnet USB Connector: Type B, connects to HiQnet network. |
Output Power | 1000W @ 2 Ohms Stereo (per Channel)800W @ 4 Ohms Stereo (per Channel)475W @ 8 Ohms Stereo (per Channel)2000W @ 4 Ohms Bridged-Mono1600W @ 8 Ohms Bridged-Mono |
Indicators | Signal Indicator: Green LED, one per channel, illuminates when a very low-level signal is present at input (may be used for troubleshooting cable runs).-10 Indicator: Green LED flashes when output signal exceeds -10 dB below clip.-20 Indicator: Green LED flashes when output signal level exceeds -20 dB below clipReady Indicator: Green LED, one per channel, illuminates when the amplifier is ready to produce audio.Clip Indicator: Red LED, one per channel, turns on at the threshold of audible distortionTemp Indicator: Red LED, one per channel, illuminates under excessive temperature conditionsPower Indicator: Blue LED illuminates when the amplifier has been turned on and has power |
Cooling | Proportional speed fan with front-to-rear airflow. |
Power Consumption | 8.3A; no more than 38W at idle |
Power Requirements | 100 VAC, 120 VAC, 220-240 VAC 50/60 Hz |
Dimensions | 19 x 3.5 x 12.25" (48.26 x 8.89 x 31.11cm) |
Weight | 18.5 lbs (8.4kg) |
Specialties | DSP Includes EQ, Crossover Filters, Delay, and Subharmonic SynthesizerProtection for Short Circuits, Overloads, and Overheating |
Controls Front Panel | Level: Two front-panel rotary level controls, one for each channel Power Switch: On/Off switch applies AC power to the amplifierSel/Prev/Next Buttons: Three buttons near the LCD screen that are used to access menu items and front panel lockoutLCD Screen: Backlit liquid crystal display that shows preset and processing status |
Damping Factor | 20Hz to 1kHz > 500 |
![]() |
Active systems are popular but a portable passive system requires less time to set up. One of our systems pairs our Crown XTI 2002 with a Crown XTI 4002 for a great sounding, light weight system.
![]() |
Excellent AMP! I regularly use these and the 4002 and the 6002 for mid sized gigs, and they are as reliable as you can get. Better for a smaller set up as they don't pack the same punch as the 4002 or the 6002.
![]() |
I purchased this in 2016, and for these last 2 years it has worked without a hiccup. Excellent functions included.
![]() |
The amp section proved to be everything that we needed it to be. We used the amp to drive both monitors and mains in a small church. The DSP was another issue. After downloading Crown's latest software to a high-end laptop and allowing the software to update, we were never able to get the DSP out of...
![]() |
After cranking my PA from 8am until afternoon I blew up an amp and was told by tech support that I'm a power user and need to go with a workhorse amp he recommended Crown XTi. Bought a XTi4002 to run 18" sub cabs.
![]() |
I love my new Crown amp. It replaces the butterflied Crown CE1000 that was onboard my JBL MPro418SP bass bin. It handles throbbing bass without breaking a sweat. This is how bass amplification should be. I will never-ever again purchase an speaker with an amp onboard (except for studio monitors).
![]() |
I bought 2 of these a few months ago, and I really love it! I use it all the time and it runs so smoothy. There's no issues with it, easy to connect. I run it on bridge, and jblbase418, it sounds amazing. Highly recommend!!
![]() |
The machine is great. Understanding how to set it to levels, well, you may need a sound engineering degree for that.
![]() |
The Crown XTi 2002 is very quite. You could put a mic in the same room and still record your music.
![]() |
Well worth the money. Crown quality at its best. Easy to set up. Powering a Peavey 218 subwoofer with this amp. Awesome punch!
- Stereo Power @ 8 Ohms: 475W x2
- Peak Plus Limiters
- Subharmonic Synthesis
- 3 User-Defined Fan Mode Controls
- In-Depth DSP Processing
- HiQnet Band Manager & System Architect
- Crown Audio XTi 2002 Power Amplifier
- HiQnet Band Manager and System Architect Control Software
- 3 Year Warranty