- Guaranteed Brand New Products
- All Products Sold by Manufacturer Authorized Retailers
- 30 Day Return Policy
No Additional Fees
|Package Weight||22.0 lb|
|Box Dimensions (LxWxH)||22.5 x 19.0 x 7.0"|
|Input Impedance||20k Ohms (Balanced)10 kOhms (Unbalanced)|
|Gain||32.9dB @ 1kHz, 8 Ohm Rated Output|
|Frequency Response||(at 1 watt, 20Hz - 20kHz) +0dB, -1dB|
|Signal-to-Noise Ratio||XTi1002/2002/4002: 100dB (A weighted)XTi6002: 103dB (A weighted)|
|Total Harmonic Distortion (THD)||< 0.5%|
|Connections||Input Connectors: XLR, one per channelLink/Out Connector: Loop-thru signal from input connector for linking another amplifier, one per channel.Output Connectors: Two Neutrik Speakon NL4MP output connectors. Channel-1 Speakon is wired with Ch. 1 and Ch. 2 outputs for use with optional single 4-conductor cable. Two binding post outputs (in parallel with Speakon connectors).HiQnet USB Connector: Type B, connects to HiQnet network.|
|Output Power||700W @ 2 Ohms Stereo (per Channel)500W @ 4 Ohms Stereo (per Channel)275W @ 8 Ohms Stereo (per Channel)1400W @ 4 Ohms Bridged-Mono1000W @ 8 Ohms Bridged-Mono|
|Indicators||Signal Indicator: Green LED, one per channel, illuminates when a very low-level signal is present at input (may be used for troubleshooting cable runs).-10 Indicator: Green LED flashes when output signal exceeds -10 dB below clip.-20 Indicator: Green LED flashes when output signal level exceeds -20 dB below clipReady Indicator: Green LED, one per channel, illuminates when the amplifier is ready to produce audio.Clip Indicator: Red LED, one per channel, turns on at the threshold of audible distortionTemp Indicator: Red LED, one per channel, illuminates under excessive temperature conditionsPower Indicator: Blue LED illuminates when the amplifier has been turned on and has power|
|Cooling||Proportional speed fan with front-to-rear airflow.|
|Power Consumption||6.8A; no more than 38W at idle|
|Power Requirements||100 VAC, 120 VAC, 220-240 VAC 50/60 Hz|
|Dimensions||19 x 3.5 x 12.25" (48.26 x 8.89 x 31.11cm)|
|Weight||18.5 lbs (8.4kg)|
|Specialties||DSP Includes EQ, Crossover Filters, Delay, and Subharmonic SynthesizerProtection for Short Circuits, Overloads, and Overheating|
|Controls Front Panel||Level: Two front-panel rotary level controls, one for each channel Power Switch: On/Off switch applies AC power to the amplifierSel/Prev/Next Buttons: Three buttons near the LCD screen that are used to access menu items and front panel lockoutLCD Screen: Backlit liquid crystal display that shows preset and processing status|
|Damping Factor||20Hz to 1kHz > 500|
Nice sounding amp. Very flexible. Could give it a higher rating if the fan wasn't so noisy.
Plenty of power. Great sound.
I used these as monitor amps in a large scale event and they were absolutely fantastic! Would highly recommend any of the XTi series amps!
looks nice, works well. It is necessary for me to use my computer to do the adjustments I need using the parametric equalizers. I I bridge the amp and use it on a "bandpass" filter so it has the cut off at the bottom frequencys to control speaker excursion and also a low pass filter to cross over...
low cost high quality and great versatility. The Crown name and the reviews I read makes me confident it is well built.
none Would have liked to see some watt output leds to see what I was feeding the speaker(s) One led at -10 (Probably 50 of the 500 available 500 watts at the brink of overload) and a second At -20 dB (5 watts) me with questionable max power being provided.